There is a huge variety of door hinges available in today’s commercial hardware market. Which hinge is right for your application? This article discusses hinge types, hinge characteristics, and basic guidelines
on how to choose a hinge for your application.
Parts of a Hinge
At right is an illustration that details the components of a full mortise hinge. Pictured is the most common hinge used in the United States, a five knuckle, full mortise ball bearing architectural grade template hinge, four-and-a-half by four-and-a-half inches.
- The leaves are fastened to the door and door frame.
- The bearings keep the hinge alligned help the hinge last longer by reducing wear
- The pin (shown slightly withdrawn from the knuckles as if being removed) holds the leaves together and provides the axis on which the door will turn
- The knuckle is a loop of metal through which the pin passes
- The top tip rests on the top knuckle of the hinge, stabilizing the pin; the bottom tip is attached to the bottom knuckle and helps keep the interior of the knuckles clean.
The leaves could be equal widths, or unequal; the leaves could be “swaged”, meaning bent to compensate for a door with a beveled edge; the bearings could be ball bearings, concealed bearings, lube bearings, or “plain bearings”, indicating no bearings at all; the pin could be non-removeable or fixed; there could be five knuckles, three knuckles, or in some cases, no knuckles; and hinge tips could be decorative or could serve a purpose, such as hospital tips, which are beveled to prevent things from getting caught on them.
Commercial architectural grade hinges could be standard weight or heavy weight; they could have square corners or round; and they could be “template” or “non-template” hinges, indicating whether its screw pattern matches architectural conventions so as to fit in standard hollow metal door preps or not.
Electrical options are also available, such as electric though wire, concealed magnetic contact, exposed electrical conctact, and others.
To measure a full mortise hinge, also called a butt hinge, lay it on a flat surface. Measure the height, then the width. When you specify full mortise hinge sizes, always refer to the height first, then the width.
Heavy Weight vs. Standard Weight Hinges
Heavy weight hinges are used for very heavy doors or doors that are subjected to very high traffic. Hinge “weight” actually refers to hinge leaf thickness. Heavy weight hinges leaves run closer to .200 gauge thickness, while standard weight hinges are more in the range .150 gauge thickness.
Hinge thickness is also dependent on hinge size. For example, a standard weight hinge 6 inches by 5 inches will be thicker than a standard weight hinge that is 4-1/2 by 4-1/2 inches.
Wide Throw Hinges
Types of Hinges
All the hinges lifted below are available in standard weightand heavy weight versions for different commercialapplications. Illustrations at right show various kinds ofhinges.
Full Mortise Hinges
As I said earlier, full mortise hinges are by far the mostcommon type of hinge. They come in a wide variety toaccommodate diverse applications.
Half Mortise Hinges
Half Surface Hinges
Half surface hinges are hinges that have one leaf mountedto the surface of the door and the other leaf mounted intoa hinge prep on the jamb part of the door frame.
Full Surface Hinges
Swing Clear Hinges
Swing clear hinges are designed so that when the door isopened to 90 degrees, the door itself is completely out ofthe opening. For example, if you needed to move a cartthrough a door that was 35-1/2 inches wide through a 36inch wide door, unless the door was hung on swing clearhinges, you would have to be able to open the door 180degrees in order to get the cart through the opening.
All of the hinges above are available in swing clear versions.
Template and Non-Template Hinges
“Template” hinges are full hinges that have a standard screw pattern and sizing to fit into an ANSI standard hinge prep, usually on a hollow metal door andframe. Most architectural (commercial) grade hinges aretemplate hinges. Most residential hinges are nontemplatehinges.
Radius corner hinges are hinges with roundedcorners. “Radius” refers to the radius of the circle thatwould exist if the curve of the rounded corner werecontinued to form a circle.Architectural hinges are available with 1/4-inch radius corners whereas residential hinges are available in 1/4-inch radius and 5/8 inch radius corners.
Residential hinges are very simliar to architectural hinges, but there are differences. As stated above,more often residential hinges are non-template hinges, but they are sized the same as architecturalhinges. Residential hinges also more often have radius corners than architectural hinges and areusually made of thinner gauge metal. Often one will see an architectural grade hinge used on exteriordoors and residential grade hinges used on doors within the dwelling.
Spring hinges are architectural hinges that are springloaded so as to shut the door. They are available in fullmortise, with or without radius corner, in most sizes inwhich other full mortise hinges are made, and areavailable in template and nontemplateversions. A full mortise spring hinge is shown at right. Beneath the full mortise spring hinge is a picture of adouble acting spring hinge for a door that swings bothways. Bommer Industries is an excellent source for a wide variety of spring hinges, as well as other architectural and residential grade hinges. It is important to note that spring hinges are not a substitute for a door closer, since spring hinges slam the door.
Continuous hinges are hinges that extend the full height of the door. They are widely used on aluminumstorefront and hollow metal applications. They are a good alternative for high frequency of useapplications where added durability is necessary. Continuous hinges are available in aluminum, steel,or stainless steel, and, like architectural hinges, are available in different types to accomodate differentconditions. Many of these configurations match those discussed in this article.
Pivot hinges are used on very heavy doors in high traffic applications and on many aluminum storefront doors. Since the weight of the door rests on the bottom pivot, thedoor does not “hang” as it does with other types of hinges, therefore there is less risk that the door will sag over time. At right is a drawing from Rixson Hardware’s pivot catalog.
Full mortise, pivot, continuous hinges and others are available with electrical options such as:
- Electric Through Wire: a number of conductors arethreaded through the hinge in order to conduct electricity from the door frame into the door (or vice versa) to power electric locks or transmit contact closure from monitor switches in the door or in the locking hardware. Available with anywhere from 2 to12 conductors, typically 24 gauge wire. 2conductor,18 gauge wire is also available.
- Concealed Magnetic Contact: a magnetic contact reed switch is concealed in the leaves of a full mortise hinge. When the door is opened, the leaves are spread apart, breaking or making the contact. HInges with concealed magnetic contact are handed.It is possible to have both the above options in the same hinge.
In situations where you have an out-swinging secured door, you can use hinges with non-removable hinge pins. Non-removable hinge pins are pins which have a groove milled in them in the middle. A set screw is threaded through the middle knuckle to mate with the groove (see picture at right) to inhibit burglars from pulling the pin and the door to gain entry. (In the picture, the center knuckle is not shown so that theset screw can be seen.)